PWM-T210
Installation Instructions
UNIVERSAL FLAT PANEL MOUNT
IN-PWMT210.R0
PWM-T210
Safety Precautions
This wall mount should be installed by qualified personnel having sufficient skill and competence to install it. Qualified installation specialists or your dealer should
install the mount and set up the plasma display in order to avoid personal injury or property damage. Premier does not assume liability for injury or damage,
including liability, caused by improper installation, mounting or setup of the plasma display, misuse, modification or natural disasters.
The entire installation instructions should be fully read and understood, including all of the safety symbols and safety precautions, before beginning installation.
The installation instructions should be read, understood and followed to prevent personal injury or property damage. Keep these installation instructions in an
easily accessible location for future reference.
The wall being considered for mounting must be capable of supporting at least five (5) times the weight of 40Kg. If it is not, the wall must be reinforced before
beginning installation.
Only use specified parts for the installation of the mounting bracket. Do not use the mounting hardware from any other mount or any other source.
Warning Statements
The wall or ceiling structure must be capable of supporting at least five (5) times the weight of the plasma display. If not, the wall or ceiling must be reinforced.
Proper installation procedure by qualified personnel as outlined in the installations instructions must be followed. Failure to do so could result in serious personal
injury.
The entire installation instructions should be fully read and understood, including all of the safety symbols and safety precautions, before beginning installation.
The installation instructions should be read, understood and followed to prevent personal injury or property damage. Keep these installation instructions in an eas-
ily accessible location for future reference.
Safety precautions must be taken at all times.
Handling by other than professional contractors is prohibited.
Warning and caution in general.
Indicates that the power plug is to be disconnected from the power outlet.
Contact Premier Mounts for any technical/installation questions.
Disassembly of the plasma display is prohibited.
Installation Location
Make sure the plasma display mounting area is completely free of
A secured structure wooden stud wall must always support the weight or load
internal or external wires, pipes, gas lines, phone lines, etc. Failure to do
of the plasma display. Always confirm the center of the wood stud before
so may result in injury and damage to the walls, wiring or piping system.
beginning the installation. Failure to do so could result in personal injury and
Do not block the ventilation holes. Sufficient clearance must be left in the
area surrounding the plasma display and wall mount to avoid blocking
the vents and causing the plasma display to overheat which could cause
physical damage.
Avoid installing the plasma display in locations where temperatures and
humidity are excessively high, or contact with any water or vapors possible.
This could result in fire, electrical shock and damage to the plasma display.
Water will damage the wall structure for wall mount installation.
The permissible temperature is (0-40ºC) and humidity is (20%-80%).
a
risk of fire. Leave 100mm or more away from all of the
surrounding four sides for proper airflow.
Do not install in locations where there is vibration, movement or danger
of impact. Failure to do so could result in plasma display cracking or
falling from the wall causing damage and injury.
The mount is designed to be used on vertical walls only. Do not install near or
on doors, angled ceilings, walls, or any other installations other than wall
mounting. Failure to do so could result in damage and injury. This wall mount
is to be used only with
plasma display other than Pioneer is prohibited and may cause injury and dam-
age.
Do not install near heater, fireplace, direct sunlight or air conditioning or
any other source of direct heat energy. Failure to do so may result in
damage to the plasma display and could cause a risk of fire.
It is not necessarily to open the plasma display prior to installation. Never
open the plasma display or modify the mount. This mount is to be used
only as outlined in the installation instruction. Failure to do so may result
in damage and injury. If a malfunction or problem occurs with the plas-
ma display display, contact the nearest dealer or Pioneer.
a
Pioneer plasma display. Use with any
Avoid Installations where there is danger of contact with over excessive dust,
oil smoke, and tobacco smoke. Failure to do so may result in fire or damage
to the plasma display or its internals.
Safety Precautions
At least two qualified people should always perform the installation work.
Injury and damage can result from dropping or bending the plasma display.
All bolts must be properly tightened and secured before installing the
plasma display. Failure to do so could result in the plasma display falling
causing damage to the plasma display and personal injury.
All hardware must be firmly tightened and secured to the plasma display in
the correct locations. If the hardware is not properly installed, do not hang the
plasma display to the wall mount. Damage and injury could result from the
plasma display falling down.
Objects on the wall may collect dust quicker than anticipated. Check
periodically for dust accumulation. Refer to the plasma display installa-
tion instructions for cleaning instructions.
Do not play around the plasma display or throw any objects near or at
the screen. The screen is very sensitive and may scratch or break or
cause the plasma display to fall from the wall causing personal injury
and damage.
All four (4) Lag bolts must be properly secured to the wall studs. The lag bolts
must always be secured through the center of the wood studs. Failure to do so
could result in the plasma display falling from the wall causing damage to the
plasma display and personal injury.
Installation Instructions
Page 3
PWM-T210
Parts List
NOTE:
This mount is shipped with all installation hardware and components. Make sure that none
of these parts are missing and/ or damaged before beginning installation. If there are parts
missing and/or damaged, please stop and contact Premier Mounts (800) 368-9700.
5/16" x 3" Lag Bolts
(Qty 8)
Wall Plates (Qty 2)
5/16" Flat Washers
(Qty 8)
Mounting Brackets
(Qty 2)
M6 x 30 Lateral Shift
Locking Screws
(Qty 2)
Griplates™
(Qty 6)
Template (Qty 1)
M6 x 12 Safety Knobs
(Qty 2)
M6 x 12mm Phillips
Head Screws (Qty 4)
M8 x 20mm Phillips
Head Screws (Qty 6)
Installation Tools
Phillips Head Screw Driver Soft Material/ Blanket
1/2" Socket and Wrench
Level (Supplied)
1/4” Drill Bit
Pencil
Tape Measure
Drill Gun
Stud Finder (Commercially Available)
Page 4
Installation Instructions
PWM-T210
Locating the Center of the Display
CAUTION: Proper installation procedure by qualified personnel as outlined in the installation
instructions must be adhered to. Failure to do so could result in serious personal injury and
possible damage to the flat panel.
WARNING: INVERT THE FLAT PANEL PLACE IT ON A SOFT, FLAT SURFACE TO PREVENT
DAMAGE TO THE FLAT PANEL. USE A BLANKET, FOAM, ETC. FAILURE TO DO SO
WILL RESULT IN DAMAGING THE FLAT PANEL. DO NOT LAY THE FLAT PANEL ON
THE FLOOR WITHOUT ANY PROTECTION TO THE GLASS. THE FLAT PANEL IS
HEAVY AND FRAGILE. AT LEAST (2) QUALIFIED PERSONNEL ARE STRONGLY
RECOMMENDED FOR INSTALLATION OF THIS PRODUCT. FAILURE TO DO SO
COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT
PANEL.
Inverted
Display
Inverted
Display
Marking the
Center of the
Display
Display
Top
Tape
Measure
C
L
Display
Bottom
C
L
Figure 2
Figure 1
2. Using a pencil lightly mark the
center of your flat panel
(Figure 2).
1. Once the flat panel is inverted, use a
measuring tape to find the center of
your flat panel measuring from
outside to outside of the chassis
(Figure 1).
Mounting Bracket Positioning
Left
Mounting
Bracket
Display Bottom
Right
Mounting
Bracket
Arrows Facing
Out
Figure 3
3. Lay the left and right mounting brackets
over the mounting points, with the stamped
arrows facing out (Figure 3).
Installation Instructions
Page 5
PWM-T210
Display
Bottom
C
L
Mounting Bracket
Align the
Mounting
Brackets
Viewing
Guide
Center
Center of
Display
Display
Bottom
Figure 4
Figure 5
4. Match the center of viewing guide
with the center line you marked in
step 1 (Figure 4).
5. The mounting brackets are designed
with a center of viewing guide on the
side of them (Figure 5).
Securing the Mounting Brackets
The Griplates™ have M4, M5, M6 and M8 hole patterns to fit the hardware that your flat panel requires.
NOTE: Your plasma uses M8 x 20 or M6 x 12 Phillips screws, use the M8, or M6, mounting points.
1. Once the mounting brackets are aligned secure the Griplate™ to the flat panel (Figure 6).
NOTE: The dimples of the top plates have to be facing up and the bottom dimples must be facing
down.
2. Pre-install two (2) M6 x 30 (mm) Phillips pan screws to the bottom of the left and right hand side
mounting brackets.
Screwdriver
DIMPLES
FACING UP
M4
M5 M6
M8
DIMPLES
FACING UP
DIMPLES
FACING DOWN
Display Bottom
DIMPLES
FACING DOWN
Figure 6
Page 6
Installation Instructions
PWM-T210
Marking the Wall
Viewing Port
Center
Mark the Wall
VIEWING PORTS
CENTER OF
VIEWING LINE
Wall Structure
MARKING THE
LINE
Figure 8
Figure 7
1. Align the center viewing port from the
carton template to the wall. Match the
center of viewing port to the center of
viewing height desired (Figure 7).
2. Mark a line on the bottom of the
carton template (Figure 8).
Marking the Bottom Mounting Points
CAUTION:
The lag bolts must be secured to the center of a stud. Use a commercially available stud finder to locate the studs
nearest to your center viewing mark.
Pilot Holes
Drill Gun
16"
Wall Plate
Level
Mounting Slots
Wall Structure
Figure 9
Figure 10
1. Place the upper portion of the bottom wall
plate to the reference line and mark the four
(4) lag bolt mounting points through the
wall plate slots on the wall (Figure 9).
3. Pilot holes are recommended. Use a 1/4”
drill bit to drill where your markings are
located (Figure 10). These pilot holes
will be for the lower mounting plate.
2. Level the wall plate with the reference
arrow pointing up to the ceiling.
Installation Instructions
Page 7
PWM-T210
Securing the Lower Wall Plate
Marked Wall
Level
Wall Plate
Wall
Plate
Template
Figure 11
Figure 12
3. When the bottom wall plate is properly
installed to the wall.
4. Lay the carton template on top of the wall
plate.
5. Lay the top wall plate on top of the
cardboard template and mark the four (4)
mounting points (Figure 12).
1. Level and secure the plate to the wall
with the reference arrow facing up to the
ceiling (Figure 11).
2. Secure the plate using the provided lag
bolts and washers.
Securing the Upper Wall Plate
Power Source
Area
Wall
Marks
Wall
Plates
Wall Plates
Figure 14
Figure 13
2. Level and secure the plate to the wall with
the reference arrow facing up to the ceiling.
3. Secure the plate using the provided lag
bolts (Figure 14).
1. Drill four (4) ¼" pilot holes in the
marked wall (Figure 13). These pilot holes
will be for the upper mounting bracket.
CAUTION: Do not over tighten the
mounting hardware.
NOTE: CHECK THE MOUNT FOR PROPER
TIGHTNESS AND SECURITY.
Page 8
Installation Instructions
PWM-T210
Mounting the Display
WARNING: AT LEAST (2) QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR
INSTALLATION OF THIS PRODUCT. FAILURE TO DO SO COULD RESULT IN
SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL.
Top
Bottom
Figure 15
1. Raise the flat panel with the mounting brackets secured to the flat panel and insert the top and bottom
hooks from each bracket to the rods from the wall plates (Figure 15).
Lateral Shift
M6 x 30 Lateral
Shift Screw
M6 x 30 Lateral
Shift Screw
Figure 16
2. Make any lateral shift adjustments and lock the display in place by tightening the two (2) M6 x 30 (mm)
Phillips screws found on the bottom of the mounting brackets (Figure 16).
CAUTION: Do not over tighten the M6 screws to the rods.
Installation Instructions
Page 9
PWM-T210
Securing the Display
M6 x 12mm
Safety Knob
M6 x 12mm
Safety Knob
Figure 17
1. Tilt the flat panel and secure the two (2) M6 x 12 mm safety knobs to each of the mounting
brackets (Figure 17).
NOTE: To remove the display from the wall simply extend the display to its maximum tilt range,
remove the two (2) M6 x 12mm Safety Knobs, push the flat panel back to it's flat position and
loosen or remove the two (2) M6 x 30 lateral shift screws and lift the unit of the wall.
Page 10
Installation Instructions
PWM-T210
Technical Specifications
Dimensions shown in (mm)/inches.
Warranty
Limited Lifetime Warranty
All Premier Mounts products carry a limited lifetime warranty from ship date against defects in materials and
workmanship. Premier Mounts is not liable for improper installation that results in damage to mounts,
adapters, display equipment or personal injury.
Contact Premier Mounts
In the event of missing and/or damaged equipment, or technical questions, the following information can help
in the completion of the installation.
Customer Service - (800) 368-9700 Ext. 224
Technical Support - [email protected]
Premier Mounts
3130 E. Miraloma Ave.
Anaheim CA 92806
Phone number: 800-368-9700 Fax: 800832-4888
Installation Instructions
Page 11
|