Content
Safety Precautions...........................................................................................................................................................3
Technical Information................................................................................................................................................. 16
Wall-Mount Installation Instructions..................................................................................................................... 17
Operation Instructions
Thank you for purchasing the PXL2770MW LED LCD monitor. Please read this guide thoroughly
before installation.
FCC RADIO FREQUENCY INTERFERENCE STATEMENT
WARNING: (FOR FCC CERTIFIED MODELS)
This
has been tested and found compliant with the limits for a Class B digital
LED LCD Monitor
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide proper
protection against harmful interference to a residential installation. This
LED LCD Monitor
generates, uses, and can radiate radio frequency energy. Harmful interference to radio
communication may be the result if it‘s not properly installed and used. However, there is no
guarantee that interference will not occur in a particular installation. If this
LED LCD Monitor
does cause serious interference to radio or television reception, resetting may correct it.
Moreover, users are encouraged to reduce interference by doing one or more of the following:
ꢀReorient or relocate the receiving antenna.
ꢀMove the
and the receiver further away from each other.
LED LCD Monitor
ꢀConnect the
into an outlet on a circuit different from that to which the
LED LCD Monitor
receiver is connected.
ꢀConsult your local dealer or a qualified technician.
FCC Warning:
To assure a continued FCC compliance, a user must use a grounded power supply cord and the
provided shielded video interface cable with bonded ferrite cores. Also, any unauthorized
changes or modifications to this
device.
would void the user‘s authority to operate this
LED LCD Monitor
Note: If necessary, shielded interface cables and AC power cord must be used to meet the
emission level limits.
1
COMMUNIQUE D’AVERTISSEMENT DE LA FCC CONCERNANT LES INTERFERENCE DE
FREQUENCE RADIO: (SEULEMENT POUR MODELES CERTIFIE PAR LA FCC)
Ce moniteur a été testé et à été trouvé conforme aux limites pour un appareil numérique de
Classe B, suivant la partie 15 des règlements de la FCC. Ces limites ont été développées pour
offrir une protection satisfaisante contre les interférences nuisibles dans une installation
résidentielle. Ce moniteur génère, utilise et peut radier de l’énergie de fréquence radio. Ceci
peut causer des interférences nuisibles à des communication radio si l’appareil n’est pas
convenablement installé et utilisé. Il n’y à néanmoins aucune garantie que des interférences
n’apparaîtront pas dans une installation particulière. Si ce moniteur cause de sérieuses
interférences à la réception de signaux radios ou télévisées, une possibilité est de réinitialiser le
moniteur. Les usagers sont aussi encouragés à corriger les interférences en appliquant une ou
plusieurs des démarches suivantes:
ꢀ Réorientez ou déplacez l’antenne de réception.
ꢀ Placez le moniteur et le récepteur plus loin l’un de l’autre.
ꢀ Connectez le moniteur à une prise différente de celle à laquelle le récepteur est connecté.
ꢀ Consultez votre revendeur local ou un technicien qualifié.
Avertissement de la FCC:
Pour assurez une conformité continue au règlements de la FCC, l’utilisateur doit utiliser un
cordon d’alimentation mis à terre et le câble d’interface vidéo protégé avec noyaux en ferrite,
fourni avec l’appareil. Chaque modification ou changement non-autorisé appliqué à ce moniteur
peut faire perdre à l’utilisateur sont droit d’opération de cet appareil.
Note: Si nécessaire, des câbles d’interface protégés et un cordon d’alimentation alternante
doivent être utilisé pour être conforme aux limites d’émission.
According to WEEE regulation, this LED LCD Monitor can't be handled as normal trash in Europe when it is
out of usage. Please refer to the recycle information on Planar’s website to handle it.
For more information on how to recycle your product, please visit http://www.planar.com/about/green/
2
Unpacking Instructions
ꢀ
Remove the LED LCD Monitor out of the package and take off the plastic bag and Polystyrene
Foam.
ꢀ
ꢀ
Pull the base from Parallel versus Panel to Vertical.
Adjust the Panel between -5° leaning forward and 20° leaning backward.
Safety Precautions
Follow all warnings, precautions and maintenance as recommended in this user’s manual to
maximize the life of your unit.
Do:
ꢀTurn off the product before cleaning.
ꢀTouch screen surface may be cleaned using a soft clean cloth moistened with mild window
glass commercial cleaners or 50/50 mixture of water and isopropyl alcohol.
ꢀUse a soft cloth moistened with mild detergent to clean the display housing.
ꢀDisconnect the power plug from AC outlet if the product is not going to be used for an
extended period of time.
Don’t:
ꢀDo not touch the LED Display screen surface with sharp or hard objects.
ꢀDo not use abrasive cleaners, waxes or solvents for your cleaning.
ꢀDo not operate the product under the following conditions:
o
o
o
o
Extremely hot, cold or humid environment.
Areas susceptible to excessive dust and dirt.
Near any appliance generating a strong magnetic field.
In direct sunlight.
ꢀIf smoke, abnormal noise or odor emits from your LED LCD Monitor, remove the power cord
immediately and call your service center.
ꢀNever remove the rear cover of your LED LCD Monitor. The display unit inside contains
high-voltage parts and may cause electric shock.
ꢀ
LED LCD Monitor
Never try to repair your yourself. Always call your service center or a
qualified technician to fix it.
ꢀ
Due to safety concerns, if the VESA mounting kit is purchased separately, please
make sure the mounting kit is UL-listed, and replaceable only by service personnel.
3
Consignes de sécurité
Respectez tous les avertissements, les précautions et conseils d’entretien recommandés dans ce
manuel de l’utilisateur pour maximiser la durée de vie de votre appareil.
A faire :
ꢀÉteindre le produit avant de le nettoyer.
ꢀLa surface de l'écran tactile peut être nettoyée avec un chiffon doux et propre imprégné d’un
nettoyant doux du commerce pour vitres ou d'un mélange à 50/50 d'alcool isopropylique et
d'eau.
ꢀUtilisez un chiffon doux imprégné d'un détergeant doux pour nettoyer le carter de l'affichage.
ꢀDébranchez la fiche d’alimentation de la prise de courant secteur si le produit ne doit pas être
utilisé pendant une période prolongée.
A ne pas faire :
ꢀNe touchez pas la surface de l’écran LED avec des objets coupants ou durs.
ꢀN'utilisez pas des produits de nettoyage abrasifs, de la cire ou des solvants pour le nettoyage.
ꢀN’utilisez pas le produit dans les conditions suivantes :
o
o
o
o
Environnement extrêmement chaud, froid ou humide.
Endroits poussiéreux ou sales.
Près d’appareils générant un fort champ magnétique.
Sous la lumière directe du soleil.
Si de la fumée, un bruit anormal ou une odeur s'échappait de votre moniteur LCD LED,
débranchez immédiatement le cordon d'alimentation et appelez votre centre de réparation.
Ne retirez jamais le couvercle arrière de votre moniteur LCD LED. L’unité d’affichage contient
des éléments où circule un voltage élevé et présentant un risque d'électrocution.
ꢀ
ꢀ
ꢀN’essayez jamais de réparer vous-même votre moniteur LCD LED. Faites toujours appel à votre
centre de service ou à un technicien qualifié pour toute réparation.
ꢀPour des raisons de sécurité, si vous achetez séparément le kit de fixation VESA,
assurez-vous que celui-ci est certifié UL, et qu’il peut être remplacé uniquement par
un technicien qualifié.
4
First Setup
Install the stand base
LED LCD Monitor
1. Lay the
flat on a table with the LED screen face down. To prevent the monitor
from being scratched, put a piece of soft cloth on the table on which the screen will be set.
2. Unpack the base, one hand hold the monitor, the other hand attach the base to the stand.
LED LCD Monitor
3. Stand the
up.
Disconnecting the stand base
LED LCD Monitor
LED LED
screen face down. To prevent the
1. Lay the
flat on a table with the
from being scratched, put a piece of soft cloth on the table on which the screen
LCD Monitor
will be set.
2. Hold the monitor down with one hand. With the other hand, use two fingers to press the
hooks down as directed below.
3. Remove the base from the stand.
6
Quick Installation
Connect either VGA, HDMI or DisplayPort Video Source from the monitor to the computer.
Make sure both monitor and computer are powered OFF. Please note. The monitor ships
with VGA and DisplayPort cables only. HDMI cable may be sourced separately from a cable
supplier.
1.
2. Connect the audio cable from audio output of computer to the audio input of the monitor.
3. Connect the earphone to the earphone output terminal of the monitor. (Earphone sold
separately).
4. Connect power cord to an AC/DC power adapter, and to a properly grounded AC outlet,
and then to the monitor.
5. Power-ON computer and then POWER-ON the monitor.
6. Set the timing mode on your computer. Recommended resolution and refresh rate is 1920 x
1080 @ 60Hz.
Figure 1:
PC
Earphone
(not supplied)
Power cable
AC Power cable
AC/DC Power
VGA cable
DisplayPort cable
adapter
Audio cable
HDMI cable
(not supplied)
9
Basic Operation and Calibration/Reset Instructions
Before using the LED LCD Monitor:
ꢀ Connect external equipment properly.
ꢀ Insert the power plug, and the power LED indicator will light orange.
Power On/Off
To turn the LED LCD Monitor on/off:
Press
button on the front. The power LED indicator light will be blue when the LED LCD
Monitor is on.
Using the OSD Menu
Use OSD menus to adjust settings by using the menu button on the front of the LED LCD
Monitor.
Displays main menu
1
Exits from OSD menu
2
Selects between VGA, HDMI, DisplayPort or Auto mode
Select the desired item when in OSD menu
▼
When not in OSD menu, directly enters Picture Mode, press 3 seconds
activates Auto Image Adjust.
Select the desired item when in OSD menu
▲
When not in OSD menu, directly enters Audio Adjust menu, press 3
seconds activates Mute/Unmute mode.
▼ + ▲
Recalls both Contrast and Brightness (when not in OSD menu)
OSD Lock Out Function
When LED LCD Monitor is in normal mode, the “OSD Lock Out” function can be enabled.
Option 1: OSD lock – all 4 buttons are locked except the “POWER” button.
Press and hold the 1 button and the ▲ button for 10 seconds to lock the OSD buttons.
The LED LCD Monitor will show an “OSD LOCKED” message for 3 seconds and the message will
disappear automatically.
Repeat this step to unlock.
10
Option 2: OSD & Power button lock – all 5 buttons including the “POWER” button are locked.
Press and hold the 1 button and the ▼ button for 10 seconds to lock all 5 buttons.
The LED LCD Monitor will show a “POWER BUTTON LOCKED” message for 3 seconds and the
message will disappear automatically.
Repeat this step to unlock.
11
Advanced Operation—OSD Menu
You can use the OSD menu to adjust various settings for your LED LCD Monitor.
Press the 1 button to display the OSD Menu, and use ▲ or ▼ to select the desired OSD menu.
Short Cuts Function from the button(s)
AUTO IMAGE ADJUST: To auto adjust Horizontal Position, Vertical Position, Phase (Fine
Tune) and Clock (H. Size) of the screen.
CONTRAST: To adjust the foreground white level of screen image.
▲: increase contrast, ▼: decrease contrast.
BRIGHTNESS: To adjust the luminance of the video.
▲: increase brightness, ▼: decrease brightness.
ECO MODE: Allows the user to change the ECO mode. Contrast and Brightness
adjustment will be disabled when ECO is active.
Press ▲ or ▼ key to adjust the ECO Mode in three levels.
OVER DRIVE: Allows the user to change the Over Drive strength. Improve the quality of
the motion pictures.
Press ▲ or ▼ key to adjust the Over Drive strength in five levels.
12
INPUT SELECT: When Input Select is pressed, change Input signal to D-SUB, HDMI,
DISPLAY PORT or AUTO.
AUDIO ADJUST: To adjust the audio functions.
VOLUME: To adjust the volume of speaker output.
MUTE: To turn the Mute ON/OFF.
AUDIO INPUT: When in HDMI input, select where the audio source comes from AUDIO
IN or HDMI. When in DisplayPort input, select where the audio source comes from
AUDIO IN or DP.
COLOR ADJUST: To select the color for improving brightness and color saturation
between COOL, NORMAL, WARM, USER COLOR, and PICTURE MODE.
COOL: Adds blue to screen image for cooler white.
NORMAL: Adds red to screen image for warmer white and richer red.
WARM: Adds green to screen image for a darker color.
USER COLOR: Individual adjustments for red (R), green (G), blue (B).
1. Press button 2 to select the desired color.
2. Press ▲ or ▼ button to adjust selected color.
PICTURE MODE: Provides an optimum display environment depending on the content
displayed. It contains 4 user-selectable presets.
• STANDARD is for general windows environment and monitor default setting.
• GAME optimized for PC game environment.
• CINEMA optimized for movie and video environment.
• TEXT optimized for text editing and viewing in a word processing environment.
INFORMATION: To display the information, regarding the current input signal coming
from the graphic card in your computer.
Note: See your graphic card user guide for more information about changing the
resolution and refresh rate.
MANUAL IMAGE ADJUST: To manually adjust the HORIZONTAL SIZE, H. /V. POSITION,
FINE TUNE, and SHARPNESS.
HORIZONTAL SIZE: To adjust the width of the screen image.
▲: increase the width of screen image, ▼: decrease the width of screen image.
H./V. POSITION: To adjust the horizontal and vertical position of the video.
H. POSITION: ▲: move screen to the right, ▼: move screen to the left.
V. POSITION: ▲: move screen up, ▼: move screen down.
FINE TUNE: To adjust the delay time of data and clock.
Press ▲ or ▼ to adjust to your preference.
SHARPNESS: To adjust the clarity of a non-Full HD Resolution (1920x1080) signal with
▲ or ▼ button.
13
SETUP MENU: To set up LANGUAGE SELECT, OSD POSITION, OSD TIME OUT, OSD
BACKGROUND and LED mode.
LANGUAGE SELECT: To allow users to choose from available languages.
OSD POSITION: Press ▲ or ▼ button to select between horizontal and vertical OSD
Position adjustment.
H. POSITION: To horizontally adjust the OSD position.
▲: move OSD to the right, ▼: move OSD to the left.
V. POSITION: To vertically adjust the OSD position.
▲: move OSD up, ▼: move OSD down.
OSD TIME OUT: To automatically turn off On Screen Display (OSD) after a preset period
of time.
OSD BACKGROUND: Allows the user to turn the OSD background On or Off.
LED: Allows the user to turn the LED Indicator On or Off.
MEMORY RECALL: To recall factory settings for Video & Audio controls.
Press button 2 to select the Memory Recall menu option.
14
Supporting Timing Modes
STANDARD
VGA
RESOLUTION
720 x 400 @ 70Hz
640 x 480 @ 60Hz
640 x 480 @ 67Hz
640 x 480 @ 72Hz
640 x 480 @ 75Hz
800 x 600 @ 56Hz
800 x 600 @ 60Hz
800 x 600 @ 72Hz
800 x 600 @ 75Hz
832 x 624 @ 75Hz
1024 x 768 @ 60Hz
1024 x 768 @ 70Hz
1024 x 768 @ 75Hz
1280 x 960 @ 60Hz
1152 x 864 @ 75Hz
1152 x 870 @ 75Hz
1280 x 1024 @ 60Hz
1280 x 1024 @ 75Hz
1440 x 900 @ 60Hz
1440 x 900 @ 75Hz
1400 x 1050 @ 60Hz
1600 x 1200 @ 60Hz
1680 x 1050 @ 60Hz
1920 x 1080 @ 60Hz
VGA
MAC
VESA
VESA
VESA
VESA
VESA
VESA
MAC
VESA
VESA
VESA
VESA
VESA
MAC
VESA
VESA
VESA
VESA
CVT
VESA
VESA
VESA
Note:
1. HDMI and DisplayPort supports 480i, 480p, 576i, 576p, 720p, 1080i, and 1080p.
2. Simultaneously press 1 and 2 keys on monitor panel to switch between similar PC timings.
Similar PC Timing on list below:
• 720 x 400 @ 70Hz / 640 x 400 @ 70Hz
Warning: Do not set the graphic card in your computer to exceed these maximum refresh rates.
Doing so may result in permanent damage to your LED LCD Monitor.
Avertissement : Ne réglez pas la carte graphique de votre ordinateur en dépassant ces taux de
rafraîchissement maximaux. Si vous le faites, cela va irrémédiablement détériorer votre moniteur.
15
Technical Information
Panel
27” TFT (with LED backlight)
On: 36 Watts (typical), 44 Watts (maximum)
Standby Mode: < 0.5 Watt
Off: < 0.5 Watt
Power Management
Displayable Resolution
Pixel Dimension
Display Color
Full HD 1920 x 1080 max. Vertical Frequency 60Hz max.
0.3114 x 0.3114 mm
16.7M
Tilt
-5°~20°
Active Display Area
Temperature
597.888 mm x 336.312 mm
Operating: 0°C ~ +40°C
Storage: -20°C ~ + 60°C
Compliance
Power
FCC-B, CE, UL/cUL
Input Voltage DC +12V --- 3.5A,
SHENZHEN HONOR (ADS-65LSI-12-1 12042G)
Input Voltage DC +12V --- 3.33A (Max.)
FSP (FSP040-DGAA1)
Audio Output
1.5W x 2
16
Wall-Mount Installation Instructions
Preparing To Install The Optional Wall Mount Arm (not included)
This LED LCD Monitor can be attached to a wall mounting arm
you can purchase separately.
Turn the power OFF then disconnect the cables from the LED
LCD Monitor before performing the procedure below.
1. Lay the LED LCD Monitor face down on a soft surface.
2. Remove the hinge cover.
3. Remove the 4 screws holding the stand to the hinge.
4. Remove the stand.
100mm x 100mm Screw
Mounting Options
Attaching The Optional Wall Mount Arm (not supplied)
Follow these steps to finish installing the wall mounting arm:
1. Place the wall mounting arm onto the back of the LED LCD
Monitor. Line up the holes of the arm with the holes in the
back of the monitor.
2. Insert the 4 screws into the holes and tighten.
3. Reconnect the cables. Refer to the User’s Guide that came
with the optional wall mounting arm for instructions on
attaching it to the wall.
4mm, 0.7 pitch
threaded holes x 4
NOTE
•
100mmx100mm VESA high hole (n=4), M4, pitch =0.7
mm screw mounting kit not included.
17
Troubleshooting
No power
ꢀ
Make sure A/C power cord is securely connected to the power adapter and the power supply
LED LCD Monitor
is firmly connected to the
.
ꢀ
Plug another electrical device into the power outlet to verify that the outlet is supplying
proper voltage.
ꢀMake sure all signal cables are installed.
Power on but no screen image
ꢀ
LED LCD Monitor
Make sure the video cable supplied with the is tightly secured to the video
output port on back of the computer. If not, tightly secure it.
ꢀAdjust brightness.
Wrong or abnormal colors
ꢀ
If any colors (red, green, blue) are missing, check the video cable to make sure it is securely
connected. Loose or broken pins in the cable connector could cause an improper connection.
LED LCD Monitor
ꢀConnect the
to another computer.
18
Planar Support
Cables and Accessories
To find cables and accessories for your Planar monitor, touch screen or other Planar products
Technical Support
warranty information and access to Planar's Technical Library for online trouble shooting.
To speak with Planar Customer Support please have your model and serial number available
and dial:
Planar Support
Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the US.
Hours: 24 hours a day, 7 days a week.
Toll or long distance charges may apply.
19
|